enterprisesoftwaresummit.com

Home > Hard Drive > Installing A 2nd Drive W/ A Raptor Using ATA

Installing A 2nd Drive W/ A Raptor Using ATA

Contents

At startup, run the CMOS Setup program and configure your BIOS so your drive is detected. At this point the machine hangs up on a black screen with a prompt (effectively a dead prompt). About CNET Privacy Policy Ad Choice Terms of Use Mobile User Agreement Help Center Western Digital Raptor From Wikipedia, the free encyclopedia Jump to: navigation, search Western Digital WD740GD The Western Well, the potential problems aren't very obvious.Did you guys have a good Labor Day?Nope. http://enterprisesoftwaresummit.com/hard-drive/installing-new-2nd-hard-drive-plus-drive-letters-questions.html

Return to Top Unix/Linux (Any Distribution) Western Digital technical support only provides jumper configuration (for EIDE hard drive) and physical installation support for hard drives used in systems running the Linux/Unix I tried changing the jumper settings (per the news article this morning) and I can verify that the drive now lets me copy large chunks of data (31GB to be exact). If you believe this post is offensive or violates the CNET Forums' Usage policies, you can report it below (this will not automatically remove the post). There is generally no need to change the default jumper setting in order to use the drive.

Sata Hard Drive Jumper Settings

BUT BEWARE one thing. This issue was easily reproduced. On the next menu scroll down and click on hard drive enclosures.

Copying smaller 20GB chunks resulted in success. Standard laptop hard drives typically only require +5V. The top window is for viewing a drive’s status, capacity, and file system. How To Install Wd Internal Hard Drive Your BIOS may have more settings than Cylinders, Heads, and Sectors; if so, simply enter 0 for them.

Retrieved 2010-04-06. ^ "Western Digital enters enterprise storage market with world's first 10,000 rpm Serial ATA hard drive". Western Digital Sata Hard Drive Jumper Settings But I had problems with these drives in my older G5 2.0 dual and the internal SATA controller, but not on the new G5 dual-core. But despite that, the bios does recognize the drives are there but I can't figure out why XP won't boot. Follow the instructions in Answer ID 3865: How to partition and format a WD drive on Windows and macOS for Windows Vista.

Get a faster & larger drive;3. Seagate Ide Hard Drive Jumper Settings Because Windows, and system, detect HD SATA and primary IDE HD in ID 0 Bus 0 ATAPI, i move my IDE HDs to secondary IDE Channel e move my DVD/CDROM to Since then I have used this external drive to completely back up people?s hard drives and have rescued Gigs of data. Preview post Submit post Cancel post You are reporting the following post: 5/12/06 Adding old hard drive to new PC with only SATA connections This post has been flagged and will

Western Digital Sata Hard Drive Jumper Settings

I was told because I wiped out a registry entry (related to the SATA drive setup) and there was a problem due to the fact Windows 2000 can't see anything over http://www.tomshardware.com/forum/276134-32-sata-master-hard-drive-hard-drive-slave I do get forgetful after a year or so though. Sata Hard Drive Jumper Settings Just a different interface!?Digital-&-Tech lists a few on eBay. Ide Hard Drive Jumper Settings I'm sure your SATA Raptor is the one with the C: letter name, since that's where you boot from.

You should evaluate the following before proceeding to install any new hardware:1. check over here Adding an additional hard drive to a Windows 7 installation: Make sure your hard drive is detected by your Serial ATA or EIDE controller. If they were 1.1, you would have to go the Internal route.Now that we've reviewed both options, what you need to decide is what you will be using the extra drive Traditionally, the majority of servers used hard drives featuring a SCSI interface because of their advantages in both performance and reliability over consumer-level ATA drives. Western Digital Hard Drive Installation Software

So far it has worked great, I hooked the drives to it and it is bootable. This setup has been perfectly stable for a few days now, even when doing large (90GB to 185GB) disk clones. -Daryl F. " Daryl posted a report on using an Hitachi Continue with the installation of Windows 2000, as instructed by the installation program. his comment is here Last I knew, the converter comes with no power adapters or other cables, so you'll also need a SATA signal cable unless a spare came with your computer.

SATA are much more plentiful (cheaper with greater cache options too), so that would be the preferred route if my machine will recognize it.Thank you. Jumper Setting On Hard Disk I have used both options with much success. It also provides our default jumper settings for most WD drives.*END Critical: Some of the instructions in the articles below are Data Destructive and cannot be undone.

If you have two optical drives (HP/Compaq machines seem to have them) then both ports will be used, so read on...The easiest, and possibly more useful if you have more than

If using FAT32, don’t create anything larger than 32GB. IIRC I already wrote somewhere in "your" thread that the WD 320 and smaller should work fine (Edit: I meant the 8 MB cache version!). anyway, yes and yes. Toshiba 2.5 Sata Hard Drive Jumper Settings I have still been unable to recover the lost data, using recovery programs, etc., I think the info is still there, but I'm not going to pay a high price to

To be used at all, an IDE port MUST have a Master device on the cable, preferably on the END connector. by cglrcng / May 17, 2006 10:25 AM PDT In reply to: Merge partitions or use it for data & applications storage.What he did was correct. I didn't change any jumper on the drives. weblink As stated it uses the same read/write head as everything else so you don't gain speed.

Hence the performance improvement. Now then, given your computer boots to the SATA drive, that still leaves 2 or 3 EIDE ports available. But that might just be the older ones.