enterprisesoftwaresummit.com

Home > How To > Installing A CD/RW Correctly. Master/slave

Installing A CD/RW Correctly. Master/slave

Contents

When physically installing the CD drive, ensure the computer is powered down and unplugged. Only by switching the drives' Master/Slave designations - and so physically switching the drives' bay positions too! - was it possible to get Windows 98 to recognise both drives properly. The letter assigned to the drive will depend on your machine's configuration. When connecting this cable to the CD-ROM drive it should be a 3 or 4 pin cable connection (see above picture). navigate here

Modify your browser's settings to allow Javascript to execute. Refer to the chart below: IDE Port Master/slave Device 1 master /dev/hda 1 slave /dev/hdb 2 master /dev/hdc 2 slave /dev/hdd 3 master /dev/hde 3 slave /dev/hdf 4 master /dev/hdg Next: Computer Assembly - Install The SATA Hard Drive Back to My Super PC - Home Page How To Build A Computer. This 80-conductor cable puts a ground pin between each control and data signal, thereby improving signal reliability. a fantastic read

Ide Cd Drive Jumper Settings

Next, connect the 40-pin IDE/EIDE interface cable (large gray ribbon cable) to the back of the CD-ROM drive. If the wrong pair is used then the drive will not slide back into the computer case with the drive rails mounted. My TutorialsBuild, Upgrade Help Computer Memory Upgrade Hard Drive Upgrade Video Card Upgrade My Super PC Even More Help MySuperPC Forums Great prices on computer parts Crucial Crucial UK & Europe There are 3 options, Cable Select, Slave and Master.

For me, it is the bottom pair that should be used. If the CD-ROM is far from the hard drives, you will need one cable for the hard drives, and another going to the CD-ROM. Or better, what's the best way to conect them?Thanks 4 answers Last reply Aug 20, 2003 More about master slave Phalanx01Aug 15, 2003, 5:51 AM Best way is to get them How To Connect Ide Dvd Drive To Sata Motherboard Since I'm using a black computer case and the Sony DVD RW drive I'm using comes with a beige faceplate (bezel) pre-installed, I'm going to change it out with the black

Alternatively, push the blank out from the inside. Reply Adam August 24, 2016 at 3:50 pm Did you have to reformat the HDD to run as a slave on the newer box? How to determine the CD drive type How do I find what CD or other disc drive I have? For instance, with the 16/12/40 CDRW, if you're using a 24x write-once blank, the maximum speed is 16x.

This document contains information on installing the hardware for an HP DVD/CD Writer IDE drive and common issues related to this hardware installation. How To Connect Dvd Drive To Motherboard Sata A single hard drive provides a vast amount of storage space. The audio cable will connect to one of the following locations: sound card, motherboard (when onboard sound present), or DVD decoder card. Connect to Sound Blaster-compatible sound card and to analogue audio output connector at the rear of the drive.

How To Connect Cd Rom To Motherboard

If you are upgrading an old SATA drive then you can use the same cables, if not then you will need to install a new cable from the motherboard to the here Once you've set the jumpers for master or slave (I use master if it's the only one on the cable), with the power supply switch set to 0, or if there's Ide Cd Drive Jumper Settings By using this document you are accepting this disclaimer. Why Is It Necessary To Partition The Hard Disk While Installing Operating System? Cable Select If the model of your HP DVD/CD Writer drive did not come with a cable, or if for some reason you must use the cable that already exists in

Carefully slide the drive out from the drive bay and put that to one side too. check over here If your CDRW is installed correctly, Knoppix should detect it and enable you to burn CD's. If the other device is jumpered as Cable Select, then jumper the HP DVD/CD Writer drive as Cable Select. You must also know the maximum speed of your CDRW, and the specified speed for the media you're using. How To Install Dvd Drive On Pc

SATA cables can only be inserted one way but ensure the cable is fully inserted. Software setup IDE/EIDE CD-ROM drives only require the one or two CD-ROM drives for the drives to work. Reply MikeTek July 10, 2016 at 6:36 pm Actually, slave is the middle connector and master is the end. http://enterprisesoftwaresummit.com/how-to/installing-on-a-slave-hard-drive.html Test it.

Please refer to the computer documentation for additional information on what is needed to install the HP DVD/CD Writer drive. Why Do Some Sound Cards Need Two Separate Sets Of I/o Addresses An alternative audio option - and one that will provide purer sound than the analogue audio connector - is to connect the CD-ReWriter's digital audio output connector to a sound card So start by confirming that the device works.

IDE cable (if required).

But if you're using a 12x write-once blank, the maximum speed is only 12x. The power cable you will plug in has four female plugs in it, and will only go in one way due to the shape of it, so that shouldn’t be too note: Disconnect the power and remove your PC's cover, see our guide. Ide Hard Drive Jumper Settings In deciding where to put this drive, please remember that simultaneously running two drives on the same IDE cable severely degrades the performance of both.

Works fine for me and I tried several combinations but this works best methinks.Is it a bad thing if there is smoke coming out of my case? If that's not acceptable to you, you may not use this document. I am not responsible for any damage or injury caused by your use of this document, or caused by errors and/or omissions in this document. weblink The master device is connected in the middle of the cable, and the slave at the end of the cable.