Installing A Modem On NT4.0
Start the Windows NT User Manager to Enable Access from the Guest Machine: Establishing the Connection Server Computer: Verify the remote access service is ready: Click OK (you may not have For NT , Check the Devices applet in the Control Panel to make sure PCMCIA support is enabled. dmoz.org Sign In Upload Page of 50 Go Download Table of ContentsContents Print This PagePrint ShareShare Url of this page: HTML Link: Bookmark Comment Manuals Brands IBM Manuals Network Card 84H5162 Type the phone number for the RAS server, click Next, and then click Finish. http://enterprisesoftwaresummit.com/installing-a/installing-a-second-cpu.html
close WindowsWindows 10 Windows Server 2016 Windows Server 2012 Windows Server 2008 Windows Server 2003 Windows 8 Windows 7 Windows Vista Windows XP Exchange ServerExchange Server 2013 Exchange Server 2010 Exchange And because modems achieve high speeds in different ways, compatibility problems increase with high-speed modems. Connect the Cables Connect the Power Adapter Be sure to only use the included power supply. If you choose a protocol that is not currently installed, you must install that protocol using the Network tool in Control Panel. http://www.rctc.edu/technology/it/dial-up/dial-up-networking-installNT4.html
Connect the Ethernet or USB Cable Follow the instructions below for the connection type (Ethernet or USB) you selected in Step 2. Click Next to launch the installation of this component, and follow the on-screen instructions. Your Remote Access parameters should have already been configured.
If you would like to change the default location, click Browse to select a new folder. Click on 'More' then 'Edit Entry' and 'Modem Properties.' Under the Server tab check only TCP/IP. Your ISP should have provided you with VPI, VCI, and Encapsulation-type parameters. The same IRQ must be selected on the card.
To print the manual completely, please, download it. Email, Voice & InternetEmail & Messaging Email Protection and Security Mail-Relays Mailing Lists Student & Alumni Email Service UBC Faculty & Staff Email (FASmail) Voice Call Centre Solutions Cell Phones Pager Connect Microfilters (If Necessary) If there are no microfilters included in your package and your ISP did not provide any, skip to Step 2 of these installation instructions. After the installation is complete, you will have installed the following items: USRobotics SureConnect ADSL USB/Ethernet Modem USRobotics SureConnect ADSL Utility NOTE: It is important that you have your serial number
You will also need to verify that your modem is installed and configured; this can be done at 'Start | Settings | Control Panel | Modems.' PART B - Configuring Dial-Up Follow the New Hardware Wizard's on-screen instructions to complete the installation of the hardware. With the current window open, go to the Remote Access menu located at the top of the screen and click Modem. Click on "OK".
Installing your particular modem on the new serial port: After adding the serial ports & rebooting your system, you will need to tell Windows NT what is connected to the ports. http://www.microsoft.com/resources/documentation/windowsnt/4/server/proddocs/en-us/network/xns06.mspx Configuring a RAS Server to Use NetBEUINetBEUI gives the best performance for NetBIOS applications in small LANs. NOTE : If you are not prompted to install Dial-Up Networking, DUN and RAS have already been installed. Click Next.
The driver will be installed as an Ethernet driver and the interface name will be called ADIModem. check over here Confirm the Sound option is set to On. Run ./inst_mod KernelSrcDirectory. For information about configuring a server to forward NetBIOS broadcasts, see "IPXRouter Parameters" in Appendix A, "RAS Registry Values." For better performance on TCP/IP networks, Windows NT clients can use WINS
This feature is available as soon as you plug the USB cable in. You may need your Windows NT 4.0 installation disks or CD-ROM. The next dialog box is the caching dialog box. his comment is here Log In or Register to post comments Patrick (not verified) on May 7, 2001 So what is the answer to the quesiton ?
Make sure the COM port number is correct for the com port you are installing. At this point you should receive a message indicating no phone books have been located. You might be prompted to confirm network protocols or other settings. 13.You must restart your computer for the Remote Access installation and configuration take effect. The Remote Access software includes the following applications:
Enter the following information in the Remote Access screen: Select the Registered User option.
Select option Driver from disk provided by hardware manufacturer 5. Sign up! One network card might be connected to your network; the second adapter could be a modem or ISDN port. Client Computer: (Client NT display) (Client NT display) (Client NT display) (Client NT display) (Client NT display) Now you should see: (Client NT display) Accessing files on the Other Computer Run
Log In or Register to post comments Ian Ragusa (not verified) on Dec 28, 2000 This article needs to be updated badly. This does not affect the performance of your high-speed Internet connection; however, it does affect the way you configure the operating system to complete the connection setup. Installation Overview & System Requirements What You Need Before You Begin ADSL and Internet service from your local telephone company or Internet Service Provider (ISP) or access to an ADSL DSLAM http://enterprisesoftwaresummit.com/installing-a/installing-a-his-x1950xtx.html Click Finish and remove the CD-ROM from the CD-ROM drive of your computer.
Click OK in the Packet Filtering dialog box. After you have built the driver, run the following script: USR_USB/./inst_pppoa 2. Before you install Microsoft Proxy Server 2.0, make sure that your system meets the following prerequisites: Your machine has Windows NT Server 4.0 installed. If you are reinstalling DUN, there may be existing phone book entries.
If you accept the default location, click Next. This base address can be found in the documentation for the Byte Runner serial card you are installing. Click Next. NOTE: Some Internet Service Providers require additional software be installed for optimum performance.
Finally, the transport layer (TCP) adds a protocol header, followed by the application protocol data. Click Yes to register your modem, and you will be brought to the USRobotics Web site.