enterprisesoftwaresummit.com

Home > Windows 98 > Installing BT Broadband Wireless Router On Windows 98 SE PC

Installing BT Broadband Wireless Router On Windows 98 SE PC

Contents

I have USB 3.0 Port on My computer & HUB, MY HP printer requires USB 2.0 Port. Check that the properties for this are set correctly: On the IP address tab ensure the Obtain An IP Address Automatically check box is selected. Finally, run the Browser Connection Setup Wizard on each of the client computers by inserting the Client Configuration Disk into the floppy disk drive and, from the Run dialog box on Yes, my password is: Forgot your password? http://enterprisesoftwaresummit.com/windows-98/installing-windows-98-over-windows-xp.html

If it still doesn't say Connected, right-click the connection, Disable. Since an IP address is a 32-bit number, it's theoretically possible to have 4,294,967,296 unique addresses. The NAT-enabled router has an IP address of 192.168.254.254 for the inside network and an address of 195.157.146.53 for the outside network. Click here for "The Story of the PING Program", as told by its author. Go Here

Windows 98 Network Settings

Windows XP comes with a firewall capability and, in the absence of a firewall-capable modem/router you should at the very least ensure that your use this or one of the many This is the best way to go, Of all info on networking on the net. USAFRetMar 12, 2014, 10:51 PM Or, you can get a USB SATA/IDE cable or dock. Note, the RTT values get progressively larger as the ICMP packets travel farther onto the Internet to reach their destination.

Connecting to the service Type the Gateway address - effectively the IP address of your modem/router - in the address bar of your browser. This is the best. Such products and are now being offered by a wide variety of sources in the UK. Hit OK two times and the setting should be saved.

The procedure is described below, for a Windows 98 environment: Windows 98: 1. Windows 98 File Sharing This might be the dumbest question ever, but if I installed something like Windows XP, would that enable me to connect to the internet on the older computer? If it isn't DSL or if it is DSL via DHCP itwill still make the connection and NO ISP software should ne needed on the PC.Besides the PPPoE connection capability, there check my blog Your help is very much appreciated it.

From the cabling to the setting up the actual IP addresses, this guide covers them all. Delete the current entry in the username box and type in the username given to you by your ISP. I have spoken to bt who > were> unhelpfull and could not work it out.> I wondered if any one else could help me I've been trying to sort this out> Thanks again.

Windows 98 File Sharing

One of the disadvantages of this arrangement was that if your computer equipment didn't happen to be close to your BT master socket, you'd have to resort to running extension cabling. You'll now be able to browse the Internet using your broadband connection! Windows 98 Network Settings We've basically configured the computers so that they can find each other. Windows 98 Network Setup solved Achieving Optimal Speeds Using BT Home Hub 5 Acer aspire zg5 canot connect to bt home hub [Router] Upgrading from BT Home Hub 3.0 BT Home Hub Unlocking and Use

Your cache administrator is webmaster. http://enterprisesoftwaresummit.com/windows-98/install-windows-98-after-windows-xp-already-installed.html Message 2 of 13 (173 Views) Reply 0 Thanks steed Grafter Posts: 94 Thanks: 2 Registered: ‎12-08-2007 Re: Connecting a Windows 98 SE PC to Broadband ‎20-04-2009 9:38 PM Options Mark The steps in the procedure are illustrated below, in the context of Windows 98: 1. Connecting the network cables: Using an appropriate unshielded twisted pair (UTP) cable, connect any port on the ADSL modem/router to the port on the network card.

If the current status is IDLE, click Change Login. Here's a Link to an Image of it: http://justdeals.org/images/1000-901101-000-IN__3.jpgI can easily Wirelessly connect about any number of PCs, Laptops, etc. Neyzim, Feb 28, 2006 #3 SacsTC Joined: Dec 30, 2003 Messages: 1,647 Is the NIC card recognized in device manager?? his comment is here If the adapter is the only item shown you will need to add a client and protocol for the adapter to use.

The following Microsoft Knowledge Base Articles contain useful guidance on trouble-shooting common network communication problems: Article 141698: "How to Use Winipcfg to View TCP/IP Settings". Built-in WiFi & Bluetooth.-I'm obviously online wirelessly; my Main connection is done with the 2Wire HomePortal 1000 HG DSL router w/ 802.11B/G wireless functionality. -In checking my Laptop's Network Connections:It's "ACTIVE" I am not quite sure what you mean by the NIC card.

Once you have the equipment, hook them up together.

Installing the network card drivers: Turn on the power to the PC. Once powered on, you ought to be able to determine whether or not things are working properly from the modem's LEDs. Check the 2nd box if you want to allow the other computer to modify your shared folder, else it will be read only. I thought, by TonyTTurner / October 17, 2006 7:05 AM PDT In reply to: Not how I remember this to work.

Also, ensure the firewalls installed in the PC allow the traffic to go through and the host to act as a listener posted 26 Nov 2007 - Reply - Permanent Link Insert the disc in the CD-ROM drive and click OK. 6. I had tried networking with Windows wizard in the past without any success, and your instrucctions worked like magic. http://enterprisesoftwaresummit.com/windows-98/installing-windows-98-in-a-seprate-partition-to-xp-pro.html Message 4 of 13 (173 Views) Reply 0 Thanks hadden Grafter Posts: 486 Thanks: 2 Registered: ‎27-07-2007 Re: Connecting a Windows 98 SE PC to Broadband ‎20-04-2009 10:58 PM Options Mark

Click More Info for further details. Just do what you used to back then by using the diskettes or drivers you find for your hardware.Bob Flag Permalink Reply This was helpful (0) Collapse - Good, but what Flag Permalink Reply This was helpful (0) Collapse - VPC doesn't need a modem by James Denison / October 1, 2016 3:32 PM PDT In reply to: Good, but what about Insert the network card into the PCI expansion slot.

This works by examining the header of the IP packet and blocking data that does not conform to certain parameters based on all or some of the following: source IP address Many come with an integrated firewall and some can handle both wired and wireless Ethernet. When connecting a node to a node, however, a crossover cable is required. This site is completely free -- paid for by advertisers and donations.

You'll need appropriate lengths of UTP Cat5 cable, and their are advantages - in terms of flexibility - if you terminate these at appropriately located RJ45 surface mounted wall boxes, rather You can do this by touching a grounded metal object. But starting your conversation this buried is hard.Make a new post with your questions. And remember to get Category 5 Ethernet Cables for each computer to connect to the device.